Aplex-technology ARCHMI-707 Instrukcja Użytkownika

ARCHMI-7XX User Manual ARCHMI-7XX 7”, 8”, 10.1”, 12.1” and 15”, Intel Atom Low Power N2600/D2550, Fanless Industrial Compact Size Panel PC User

9

98 Control Panel Open Control Panel Windows Beep Setting Beep function for each device Right Button When you select this function, a mouse icon appe

99 5.2.2 Software Functions (Projected Capacitive) General In this window, you can see there is USB Controller. Click OK to continue. Monitor Ma

100 Setting Beep Beep On Touch Beep On Release Beep From System Beep

101 Option Function Enable Constant Touch Enable Auto Right Click Enable Touch Enable Cursor Stabilization Constant Touch Area

102 Tools Click OK to continue the settings. 4 Points Calibration Do 4 points alignment to match display

103 Display In this window, it shows the mode of display. Enable Multiple Monitors. Map to main display if system has only one display monitor Ful

104 Other Other mode of display. Quarter1~4 and Customized area. Active Area Drag active area to enable Active Area Function.

105 Hardware Saturn Hardware Configuration

106 About To display information about eGalaxTouch and its version.

10 1.2 Dimensions Figure 1.1: Dimensions of ARCHMI-707(P)

11 Figure 1.2: Dimensions of ARCHMI-708(P)

12 Figure 1.3: Dimensions of ARCHMI-710(P)

13 Figure 1.4: Dimensions of ARCHMI-712(P)

14 Figure 1.5: Dimensions of ARCHMI-715(P)

15 1.3 Brief Description of ARCHMI Series There are 7”, 8”, 10.1”, 12.1”, 15”, Industrial Compact Size Panel PC in ARCHMI series, which comes wit

16 Figure 1.7: Rear View of ARCHMI -707(P)/ARCHMI -708(P) Figure 1.8: Rear View of ARCHMI-710(P) Figure 1.9: Rear View of ARCHMI -712(P)/ ARCHMI

17 1.4 Installation of HDD (ARCHMI-707/708(P)) Step 1 There are 2 screws to deal with when enclosing or removing the chassis. Gently remove 2 s

18 Step 4. You can replace SSD card by unscrewing 4 screws as shown in the picture. Note: 4 screws are packed in the packing list. Step 5 There i

1 Revision History Reversion Date Description 1.0 2013/05/09 Official Version 1.1 2013/09/25 Modify Dimension and Net Weight Specification, add noti

19 1.5 Installation of HDD (ARCHMI-710(P)) Step 1 There are 2 screws to deal with when enclosing or removing the chassis. Gently remove 2 screw

20 Step 4. There is a SD hole in the side of machine. You can replace SD card from there. 1.6 Installation of HDD (ARCHMI-712/715(P)) Step 1 The

21 Step 3 You can remove HDD by unscrewing 4 screws in the HDD bracket. Note: 4 screws are packed in the packing package. Step 4 There is a SD hole

22 1.7 VESA Mounting The ARCHMI series is designed to be VESA mounted as shown in Picture. Just carefully place the unit through the hole and tighte

23 Chapter 2 Hardware 2.1 Motherboard Introduction SBC-7106 is a 4" industrial motherboard developed on the

24 BIOS AMIBIOS Storage 1 x SATA Connector (7P) 1 x SATA Connector (7P+15P) 1 x SD Socket (USB to SD) Ethernet 2 x PCIe Gbe LAN by Realtek RTL8111E

25 Switches and LED Indicators 1 x Power on/off switch (CN1) 1 x Reset switch (CN1) 1 x Power LED status (CN1) 1 x HDD LED status (CN1) 1 x Buzzer Ex

26 2.2.1 Jumpers Setting and Connectors Board Top Figure 2.2: Jumpers and Connectors Location_ Board Top Board Bottom Figure 2.3: Jumpers and Conn

27 2.3 Jumpers Setting and Connectors 1. JP5: (2.0mm Pitch 1X2 box Pin Header),ATX Power and Auto Power on jumper setting. JP5 Mode Open ATX Powe

28 Model DC_IN1 SBC-7106-N2600 180°Connector SBC-7106-N2600-P 45°C onnector SBC-7106-D2550 45°C onnector 5. CPU_FAN1: (2.54mm Pitch 1x3 Pin Header),

2 Warning!________________________ Avertissement!___________________ Risque de choc électrique - Ne pas faire fonctionner la ma

28 7 HDMI1: (HDMI 19P Connector), High Definition Multimedia Interface connector. 8. JP1: (2.0mm Pitch 2x3 Pin Header),COM1 jumper setting, pin

29 Step 2: Remove the storage cover Step 3: Unscrew the storage tray Step 4: Remove the storage tray

30 Step 5: The function switch setting shows up 10. S_422: (Switch), COM1 setting, it provides selectable RS232 or RS422 or RS48

31 BIOS Setup： Advanced/W83627UHG Super IO Configuration/Serial Port 1 Configuration【RS-232】 RS422 (option): Pin# Signal Name 1 422_RX+ 2 422_RX- 3

32 13. COM2: (Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. Pin# Signal Name

33 1 +DC5V 2 Ground Note: Output current of the connector must not be above 1A. 18. SATA2: (SATA 7Pin), SATA Connectors, one SATA connectors are

34 High-speed USB 2.0 allows data transfers up to480 Mb/s ,support USB full-speed and low-speed signaling. Each USB Type A Receptacle (2

35 LA_CLKP 22 21 LA_CLKN Ground 24 23 Ground Ground 26 25 Ground USB1 USB1_P 28 27 USB1_N USB1 USB0 USB0_P 30 29 USB0_N USB0 5V_USB01 32 31 5V_USB0

36 COM3 BIOS Setup： Advanced/W83627UHG Super IO Configuration/Serial Port 3 Configuration 【RS-422】 Advanced/W83627UHG Super IO Configuration

37 32. H3/H4/H5/H6: CPU1 and U53 Heat Sink SCREW HOLES, Four screw holes for intel N2600 and NM10 Heat Sink assemble. 33. H1/H2: MPCIE1 SCREW HOLES,

3 Caution Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batterie

38 SIM1： (SIM Socket 6 Pin), Support SIM Card devices. PS2： (2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be connected

39 JP5 Pin# Function Close 1-2 RI (Ring Indicator) (default) Close 3-4 COM5 Pin9=+5V (option) Close 5-6 COM5 Pin9=+12V (option) COM5： (Type DB9),

40 Pin# Signal Name 1 DCD# (Data Carrier Detect) 2 RXD (Received Data) 3 TXD (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Re

41 CN3： (1.27mm Pitch 2X30 Pin Header),connect to SBC-7106 CN3 pin Header. LED1： Mini PCIe devices LED Status. PS2： (2.0mm Pitch 1X6 Pin Wafer),

42 JP5： (2.0mm Pitch 2x3 Pin Header), COM5 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM5 port. JP5 Pin# Function Close 1-2

43 COM6： (Type DB9), serial port, standard DB9 serial port is provided to make a direct connection to serial devices. COM6 port is controlled by p

44 CN3： (1.27mm Pitch 2X30 Pin Header), connect to SBC-7106 CN3 pin Header. M-PCIE1： (Socket 52Pin), mini PCIe socket, it is

45 PS_ON2（option）： (2.0mm Pitch 1X2 Pin Wafer), They can be used directly via cable connection to SBC-7106 JP5. PS_ON2 SBC-7106 R1.10 /JP5 Pin1

46 Signal Name Pin# Pin# Signal Name 5V_USB23 1 2 5V_USB23 USB3_N 3 4 USB2_N USB3_P 5 6 USB2_P Ground 7 8 Ground NC 9 10 Ground Note: Before conn

47 JP6 (2.0mm Pitch 2x3 Pin Header), COM6 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM6 port. JP3 Pin# Function Close 1-2 R

4 Packing List Accessories (as ticked) included in this package are: □ Adaptor □ Driver & manual CD disc □ Other.___________________(please s

48 37. TB-528CAN2 R0.10（option）: SBC-7106 Riser Card,TB-528CAN2 CN3 connect to SBC-7106 CN3 pin Header. It provides two CAN-bus Interface. TB-528CA

49 PS2： (2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be connected to PS/2 keyboard or mouse via a dedicated cable for di

50 COM6： (2.0mm Pitch 2X5 Pin Header), COM6 Port, up to one standard RS232 port are provided. They can be used directly via COM cable connection. Si

51 Pin# Channel Signal Name Function 1 CAN2 CANL2 CAN bus Signal L 2 R2- Terminal resistor R-(internally connected to CANL2) 3 FG Shield cable

52 Chapter 3 BIOS Setup 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation, Press [Delet

53 3.3 Main Settings

54 System Time: Set the system time, the time format is: Hour: 0 to 23 Minute: 0 to 59 Second: 0 to 59 System Date Set the system date, the date f

55 [96 PCI Bus Clocks] [128 PCI Bus Clocks] [160 PCI Bus Clocks] [192 PCI Bus Clocks] [224 PCI Bus Clocks] [248 PCI Bus Clocks]

56 3.4.3 CPU Configuration Processor Type Intel(R) Atom(TM) CPU N2600 EMT64 Not Supported Processor Speed 1600MHz System Bus Speed 400MHz Ratio Sta

57 Passive TSP Value 10 3.4.5 IDE Configuration SATA Port0 Not Present SATA Port1 Not Present SATA Controller(S): Configure SATA as:

5 Table of Contents Revision History……………………………………………………………………………………………………1 Warning!/Avertissement!...………

58 3.4.7 W83627UHG Super IO Configuration W83627UHG Super IO ch W83627UHG Serial Port 1 Configuration UART Mode Selection： [RS-232] [RS-485] [RS

59 Console Redirection [Disabled]

60 3.5 Chipset Settings 3.5.1 Host Bridge ►Memory Frequency and Timing ►Intel IGD Configuration ******* Memory

61 [Disabled] Max TOLUD [Dynamic] [1GB] [1.25GB] [1.5GB] [1.75GB] [2GB] [2.25GB] [2.5GB] [2.75GB] [3GB] [3.25GB] Intel IGD Configuration IGFX – Bo

62 Active LFP IGD Clock Source Fixed Graphics Memory ALS Support Back light Control Back light Logic Back light Control Lev

63 3.5.1 South Bridge TPT Devices PCI Express Root Port 0 PCI Express Root Port 1 PCI Express Root Port 2 PCI Express Root Port 3 DMI Link ASPM Cont

64 Setup Prompt Timeout [1] Bootup Numlock State [On] [off] Quiet Boot [Disabled] [Enabled] Fast Boot [Enabled] [Disabled] Skip VGA [E

65 Launch Video OpROM po [Do not Launch] [UEFI only] [Legacy only] Other PCI device ROM [UEFI OpROM] [Legacy OpROM] 3.7 Security Settings

66 Type the password with up to 20 characters and then press <Enter> key. This will clear all previously typed CMOS passwords. You will be requ

67 Save Changes and Exit Save & Exit Setup save Configuration and exit? [Yes] [No] Discard Changes and Ext Exit Without Saving Quit without savi

6 Chapter 5 Touch Screen Installation 5.1 Windows 2003/XP/Vista/7 Universal Driver Installation for PenMount 6000 Series……

68 Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows 7.

69 4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Select Intel (R) Chipset NM10 Express from

70 Step 3. Read the license agreement. Click Yes to accept all of the terms of the license agreement. Step 4. Click Next to continue.

71 Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. Click Finish, then remove any installation media from the drives

72 4.2 Intel Graphics Media Accelerator Driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1.Select Int

73 Step 3. Read license agreement. Click Yes. Step 4. Click Next.

74 Step 5. Click Next. Step 6. To restart the computer, select Yes, I want to restart this computer now. Then click Finish.

75 4.3 Intel (R) Network Adapter To install the Intel (R) Network Adapter device driver, please follow the steps below. Step 1. Select LAN Driver.

76 Step 3. Click Next to continue. Step 4. Click Install to begin the installation.

77 Step 5. Click Finish to exist the wizard. 4.4 Realtek ALC662 HD Audio Codec Driver Installation To install the Realtek ALC662 HD Audio Codec Driv

7 Chapter 1 Getting Started 1.1 Specifications ARCHMI -707(P) ARCHMI -708(P) ARCHMI -710(P) ARCHM -712(P) ARCHMI -715(P) System

78 Step 2. Click Next to continue. Step 3. Click Yes, I want to restart my computer now. Click Finish to complete the installation.

79 Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your touch screen work w

80 Step 2. Select Resistive Touch. Step 3. Click Next to continue.

81 Step 4. Read the license agreement. Click I Agree to agree the license agreement. Step 5. Choose the folder in which to install PenMount Wind

82 Step 6. Wait for installation. Then click Next to continue. Step 7. Click Continue Anyway.

83 Step 8. Click Finish to complete installation. 5.1.2 Installing Software (Projected Capacitive) Step 1. Insert the product CD, the screen below w

84 Step 2. Select Projected Capacitive. Step 3. Click Next to continue.

85 Step 4. Select I accept the terms of the license agreement. Click Next. Step 5. Tick Install RS232 interface driver. Click Next.

86 Step 6. Select None. Click Next. Step 7. Click OK. Step 8. Tick Support Muti-Monitor System. Click Next.

87 Step 9. Go to C:\Program Files\eGalaxTouch. Click Next. Step 10. Click Next.

8 Backlight Lifetime 20,000 Hrs 40,000 Hrs 50,000 Hrs Touch Screen Type Resistive Touch / Projected Capacitive Touch (for P model) Interface RS-232 /

88 Step 11. Tick Create a eGalaxTouch Utility shortcut on desktop. Click Next. Step 12. Wait for installation.

89 Step 13. Click Yes to do 4 point calibration. 5.2 Software Functions 5.2.1 Software Functions (Resistive Touch) Upon rebooting, the computer au

90 Calibrate This function offers two ways to calibrate your touch screen. ‘Standard Calibration’ adjusts most touch screens. ‘Advanced Calibration

91 NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced C

92 click Advanced Calibration. Step 4. Select Device to calibrate, then you can start to do Advanced Calibration. NOTE: Recommend to use a styl

93 Plot Calibration Data Check this function and a touch panel linearity comparison graph appears when you have finished Advanced Calibration. The b

94 About This panel displays information about the PenMount controller and driver version.

95 Multiple Monitors Multiple Monitors support from two to six touch screen displays for one system. The PenMount drivers for Windows 2003/XP/Vista

96 3. Touch each screen as it displays “Please touch this monitor”. Following this sequence and touching each screen is called mapping the touch s

97 6. ”Touch this screen to start its calibration” appears on one of the screens. Touch the screen. 7. “Touch the red square” messages appear. Touc